(469) 778-0871

Gate and Fence Contractor in Rockwall

Our direct employees install and repair gates and fences and build outdoor structures in Rockwall, with layout and drainage checked first.

For Rockwall property owners, Star Gate And Fence installs automatic and custom iron gates, repairs gates and electric operators, and builds wood, vinyl, wrought iron and chain link fences. We also handle concrete driveways, gate pads, hardscaping and carports. Material selection starts with the parcel’s fence standards and available construction space.

Every job is done by our direct employees, never subcontractors. Founder Elia Amiel works in the field. We check the opening, existing supports and drainage before defining the work. Gate installations address ASTM F2200 and UL 325 compliance, including gate construction and operator safety.

Request a site visit See our projects
Galvanized chain-link fence with steel posts and blue caps along a paved area, green landscape behind

Ground conditions shape the layout.

Teal and white chain link fence with diagonal sunlight shadows.

Residential zoning ranges from zero-lot-line districts to acreage districts. That changes how much room is available for gate travel, fence runs and construction access. We measure the actual opening and working space before choosing a gate layout. A wide driveway alone does not establish that a sliding gate has enough space beside it.

Drainage planning must account for existing flow paths and proposed grading. A gate pad or driveway can interrupt runoff if its elevation is chosen without checking the surrounding ground. Where floodplain constraints apply, placement and grading need coordination before the concrete layout is finalized. Customers should share existing drainage or grading plans during assessment.

We check footing locations and ground conditions rather than assuming every parcel has the same soil. Where expansive black clay is present, wetting and drying can move shallow supports and pull a gate out of alignment. Our concrete footing work follows the one-third depth rule.

We build gates, fences and outdoor structures.

Automatic Gate Installation

We size the gate, supports and operator around the opening and available travel space. Local lot configurations make these measurements part of the initial layout, particularly where space beside the driveway is limited. Our automatic gate installation work addresses ASTM F2200 and UL 325 compliance. Hardwired electrical work is identified in the permit scope.

Gate and Operator Repair

A gate that drags or stops needs its supports, travel hardware and operator checked together. We diagnose alignment and mechanical resistance before deciding which components need repair. Our gate repair work also considers local drainage paths around pads and supports. When the repair includes electrical work, we identify the applicable city permit and inspection requirements.

Wood Fence Installation

Cedar selection and fence layout must meet the applicable residential standards. In established areas, solid residential fencing requires cedar at least 1/2-inch thick. Established-area fences not governed by a Planned Development ordinance must be architecturally compatible with existing fences’ design, materials and colors. We check these requirements before selecting boards and setting the replacement fence line.

Wrought Iron Fence Installation

Lots beside perimeter roads, open spaces, greenbelts and parks require transparent wrought iron fencing under the cited residential standards. That can rule out a proposed wood privacy fence along the affected boundary. We plan wrought iron fencing around the required placement, panel layout and gate openings, checking parcel-specific requirements before fabrication and installation.

Concrete and Hardscaping

We build concrete driveways, gate pads and hardscaping with surrounding elevations considered in the layout. Local drainage standards account for topography, flow paths and changes in grading or land cover. We check where runoff travels before setting pad elevations. Where floodplain constraints apply, those constraints need to be resolved before placement is finalized.

Carport Installation

Carport placement starts with the vehicle area, support locations and room for construction access. The city’s varied lot districts and parcel-specific overlays make zoning review part of that layout. We include the applicable permit paperwork in the scope and check how the proposed structure relates to driveway use and drainage before installing the supports.

Approvals come before the final layout.

The City of Rockwall Building Inspections Department issues permits and conducts inspections for covered fence, concrete, driveway, carport and electrical projects. We prepare the paperwork and schedule inspections through the Cityworks Public Portal. Electrical work requires a city permit, so we identify hardwired operator and access-control work when preparing the gate scope.

Parcel-specific overlays and planned-development requirements can affect fence materials and placement. We check those requirements before finalizing the design. If the property belongs to an HOA, its governing documents determine whether architectural review is required. Share those documents during planning so the written scope can address association requirements alongside the city permit process.

Permits issued by: City of Rockwall Building Inspections Department

How we build in Rockwall

The same engineering standards apply on every job, whatever the property.

  • Direct employeesOur own crews set every post, pour every footing and wire every operator. We never use subcontractors.

  • Footings to depthStructural posts go into concrete to the one-third depth rule, so expansive clay cannot heave them out of line.

  • Safety standardsAutomated gates are built to ASTM F2200 geometry and wired to UL 325, with sensors tested before handover.

We establish the scope before digging.

We carry the measurements, approvals and installation requirements through the following steps.

  • Assess the site, measure openings and fence runs, and check drainage paths.
  • Request the utility locate before digging and review markings against footing locations.
  • Write the scope, identifying materials, permit requirements and applicable HOA paperwork.
  • Install with our direct employees, following the one-third depth rule for concrete footings.
  • Walk through the completed work, testing gate travel, controls and safety sensors where installed.

Where we work in Rockwall

Windmill Ridge Estates, Lynden Park Estates

Nearby cities we also serve

Garland, Mesquite, Richardson, Allen, Plano, Dallas

What affects the cost in Rockwall

For a Rockwall project, cost depends on the fence length or gate opening, material, support condition and access for construction. An existing fence may need more than replacement panels if its posts have moved. Gate repair scope depends on whether the problem starts in the structure, travel hardware, operator or controls.

Local design requirements also affect the scope. Required iron fencing, corner-lot setbacks or masonry-column requirements can change a proposed replacement. Concrete and carport work must account for grading and drainage as well as placement. We identify those conditions and applicable permit work before preparing the written quote.

Questions from Rockwall property owners

Can I replace my existing fence with the same material?
Not necessarily. The residential fence requirements prohibit spruce fencing and oil- or latex-based fence paint under the established-area standards. An existing fence may therefore use materials that cannot be repeated in its replacement. We verify which standards govern the property before specifying replacement materials.
What changes when my fence borders a street?
Under the cited residential standards, corner-lot fences beside a street require at least a five-foot setback and masonry columns at 45-foot on-center spacing. We measure from the affected boundary when laying out the proposed run. Allow space for both the setback and the columns rather than assuming the existing fence line can remain.
Does a hardwired gate operator need an electrical permit?
Yes, when the installation involves electrical work. Plan for the electrical inspection as well as the permit application. We include both in the project scope so the approval process accounts for the hardwired equipment, rather than treating the work solely as a gate installation.
What should an HOA board confirm before perimeter fence work?
Confirm who is responsible for the affected boundary. City standards assign maintenance of common areas and perimeter subdivision fencing to the HOA. The subdivision perimeter standard calls for six-foot tubular-steel or wrought-iron-type fencing with masonry columns, landscaping and entry features. Board planning should account for that full scope.

Start planning your Rockwall gate or fence.

Call (469) 778-0871 with your location, gate width or fence length, noting street-facing boundaries so we can assess site setbacks and quote in writing.

Contact Star Gate And Fence See our projects
Gates Fences Gate Repair Gate Installation Outdoor Construction Carports