Gate and Fence Contractor in Garland

Garland fence layouts start with placement rules; our direct employees install and repair gates and fences and build outdoor structures.

Garland prohibits driveway gates from swinging into public rights-of-way, so we check the full opening path before choosing a layout. Our work covers automatic and custom iron gates, gate repair, and wood, vinyl, wrought iron and chain link fences.

Only our direct employees perform the work; we never subcontract jobs. Founder Elia Amiel works in the field. Expansive black clay can shift supports and cause failures, so footing depth matters. Our gate work follows ASTM F2200 and UL 325.

Request a site visit See our projects

Fence Placement Determines the Build

Creek floodplain can affect work beyond the immediate water’s edge. Mapped areas follow Duck, Rowlett and Spring creeks and their tributaries, so proximity to a creek warrants checking the property’s floodplain status before settling on a construction footprint. The city’s floodplain guidance informs that check. New development in these areas is reviewed under the Flood Damage Prevention ordinance. For affected properties, plan for possible engineering review before committing to fence, concrete or drainage layouts.

Changes in soil moisture also matter below ground. Expansive black clay swells when wet and shrinks as it dries. That movement can heave shallow posts or leave supports uneven, changing how fence panels and gates line up. We apply the one-third depth rule to concrete footings to address shallow support placement. Drainage planning belongs alongside footing planning because water movement and the soil supporting the structure are connected.

Gate, Fence and Concrete Services

Automatic Gate Installation

We install automatic gates with ASTM F2200 and UL 325 compliance. Local rules prohibit driveway gates from swinging into an alley, city street or other right-of-way. We check the full travel path before choosing the gate position and operator arrangement. Our automatic gate systems work also serves commercial properties and HOA entrances.

Gate and Operator Repair

We check the gate’s physical movement alongside the electric operator before defining the repair. A binding gate and an electrical fault need different work. Because local electrical repairs require permits, we identify electrical tasks separately in the repair scope. Our gate repair work includes checking supports, alignment and hardware before deciding which components need attention.

Sliding Gate Installation

We assess the side clearance, driveway grade and support layout for sliding gate installation. A sliding layout can avoid a swing path that would extend into a public right-of-way, but it still needs room to travel beside the opening. We mark the proposed gate location on the survey or scaled drawing used for fence review.

Wood Fence Installation

We set wood fence dimensions from the yard location and measured grade. Rear-perimeter height is measured from inside the property, while front-yard wood fences have a lower limit. For an opaque fence on a qualifying corner lot, we account for the required visibility clip before ordering materials. Deed and HOA material restrictions also need checking before construction.

Wrought Iron Fence Installation

We plan wrought iron fence panels, posts and gate openings around the approved boundary layout. Front-yard wrought-iron fences may reach 3.5 feet, so a rear-yard enclosure design cannot simply be carried forward unchanged. We confirm the proposed material against applicable subdivision restrictions and identify any pier inspections needed before concrete is poured.

Concrete and Hardscaping

Our concrete work includes driveways and gate pads, with hardscaping for adjoining outdoor areas. Near mapped creek floodplain, proposed work may need additional review under the city’s Flood Damage Prevention ordinance. We examine the planned footprint and water path together so the scope accounts for drainage before the concrete layout is finalized.

Prepare the Layout for Approval

The city requires fence permits for first-time installations, corner-lot work, pool-yard fences, and changes in height, location or materials. Applications should include a property survey or scaled drawing with proposed fence and gate locations marked. We use the city’s fence requirements to check the scope, prepare the paperwork and schedule inspections.

Electrical repairs and installations require permits, so a hardwired gate operator or access-control installation may need a separate electrical permit. We identify that work in the scope rather than treating it as fence work alone. Where deed or HOA restrictions apply, material selection needs a separate check. Required HOA architectural approval must be obtained separately from the city fence permit before construction.

Permits issued by: the local building department

How we build in Garland

The same engineering standards apply on every job, whatever the property.

Direct employeesOur own crews set every post, pour every footing and wire every operator. We never use subcontractors.
Footings to depthStructural posts go into concrete to the one-third depth rule, so expansive clay cannot heave them out of line.
Safety standardsAutomated gates are built to ASTM F2200 geometry and wired to UL 325, with sensors tested before handover.

From Site Measurement to Gate Testing

For fences with piers, we build the required pre-pour and post-construction inspections into this process.

At the first visit, measure boundaries and openings for the survey or scaled drawing.
Before excavation, request the 811 utility locate and check markings against planned post positions.
Document the written scope, required city permits and separate HOA approval paperwork.
Direct employees install the work, applying the one-third depth rule to concrete footings.
Finish with a walkthrough, operating gates and checking safety sensors where installed.

Where we work in Garland

Chandler Heights, Club Creek, Fairways at Firewheel

Nearby cities we also serve

Richardson, Rockwall, Dallas, University Park, Mesquite, Highland Park

What affects the cost in Garland

For Garland projects, fence location can change the scope as much as material selection. A front-yard enclosure uses different height limits from a rear-perimeter fence. A qualifying corner lot may need a visibility clip. We account for those layout requirements before calculating materials, supports and installation work.

Existing posts, gate hardware, concrete condition and equipment access also affect what needs repair or replacement. Permit paperwork, electrical work and required pier inspections belong in the scope. Where floodplain review applies, that review can affect the proposed layout. The written quote identifies the work included without assuming every existing component can remain.

Questions from Garland property owners

Does replacing my fence require a city permit?

A permit is required when the work changes fence height, location or materials. First-time installations, corner-lot work and pool-yard fences also require permits. Tell us what will change and provide any existing survey. We compare the proposed scope with those categories before preparing the application.

How tall can my front or rear fence be?

For residential rear-perimeter fences, the limit is eight feet from inside grade. In front yards, wood and wrought iron may reach 3.5 feet; brick and masonry may reach only 2.5 feet.

Can my driveway gate swing toward the alley?

Toward the alley is possible only if the gate stays entirely on private property throughout its movement. If your setback cannot accommodate the open gate, we assess a different position or a sliding layout with sufficient side clearance.

Will a hardwired gate operator need another permit?

Yes, electrical installation or repair requires a permit. Describe whether the proposed work involves a new operator, access controls or an existing electrical fault so we can identify the applicable permit requirements.

Plan Your Garland Gate or Fence Project

Tell us if your fence occupies a corner lot; include location and gate width or fence length for site assessment and a written quote.

Contact Star Gate And Fence See our projects

Gates Fences Gate Repair Gate Installation Outdoor Construction Carports