(469) 778-0871

Gate and Fence Contractor in Celina, TX

With Celina’s fence setbacks guiding layout, our direct employees install and repair gates, fences and outdoor structures.

Within Celina city limits, wood fences require galvanized steel posts set in concrete, which determines our support specifications. We install wood, vinyl, iron and chain link fencing, concrete driveways, gate pads and carports. Our direct employees perform every job, never subcontractors.

Our gate installation and repair includes automatic systems and custom iron gates. Automatic gate work follows ASTM F2200 and UL 325. Expansive black clay can shift DFW fence posts, so we apply the one-third depth rule for concrete footings alongside city minimums. Founder Elia Amiel works in the field.

Request a site visit See our projects

Plan Footings and Fence Lines Together

Wood-fence dimensions determine the excavation required under the city’s fence requirements. Within city limits, fences under seven feet require posts no more than eight feet apart, with concrete footings at least 24 inches deep. Taller fences require 36-inch footings. Vertical posts must be galvanized steel and at least 2⅜ inches in diameter. These specifications affect the number of post holes, their depth and the concrete needed. Fence height therefore needs to be settled before excavation begins, rather than changed after supports are installed.

Landscaping plans also need to account for seasonal water restrictions. Under Stage 2 conservation rules, outdoor irrigation is limited to one designated day weekly and prohibited between 10:00 AM and 6:00 PM. Plant establishment must fit that watering schedule. In freezing weather, overspray can become ice on driveways and walkways, so water reaching paved access areas is another condition to consider around an entrance.

Gates, Fences and Outdoor Construction

Automatic Gate Installation

Entrance placement must fit the approved fence layout. On corner lots within city limits, we measure the fence setback before positioning gate posts and checking vehicle clearance. Our automatic gate installation includes the gate, operator and controls, with ASTM F2200 and UL 325 compliance. We confirm the permit route for associated structures and hardwired equipment before installation.

Gate and Operator Repair

We check structural movement before treating a gate problem as an operator failure. Our gate repair work addresses the gate structure alongside powered operation. Because the city’s building-permit requirement includes repairs and alterations to structures, we confirm the applicable category before defining the work. Automatic gate repairs account for ASTM F2200 and UL 325 compliance.

Wood Fence Installation

Post specifications are part of the design, not a later material choice. The city requires galvanized steel vertical posts set in concrete, which determines how we support the rails and boards. We establish fence height before specifying footing depth and spacing. Along regulated open-space edges, we check where a wood fence must transition to the required open steel construction.

Iron and Metal Fencing

A boundary beside a creek or dedicated open space needs a different design from a privacy run. Within city limits, these edges require black tubular steel fencing with at least 50% openness. Our iron and metal fencing scope identifies the applicable boundary, panel construction and openings. We keep the proposed fence outside drainage easements.

Concrete and Hardscaping

We build concrete driveways and gate pads and address adjoining hardscaping. Gate-pad placement follows the approved entrance layout, so corner-lot fence setbacks need checking before concrete is placed. We also review surface drainage at the work area. The city warns that freezing overspray can ice driveways, making water movement near the entrance a useful site-assessment item.

Carport Installation

Carport planning starts with the structure’s footprint and vehicle access. We define supports and anchoring together, then confirm the applicable permit category with Building Services for work inside city limits. The city requires permits for construction and improvement of structures. We include the proposed carport and associated concrete work in the scope used for that review.

Confirm Permits Before Ordering Materials

Permit applications and inspections go through the City of Celina Building Services Division for work within city limits. A building permit is required to construct, alter, repair or improve a building or structure. Before installation, we ask the division which permit categories apply to the proposed fence or gate. Hardwired gate operators also need confirmation of the applicable electrical permit and inspection route.

Our permit work includes preparing the paperwork and scheduling required inspections. Where HOA architectural review applies, we request the association’s requirements before finalizing the submission. Those documents guide our review of the proposed height, finish and layout alongside city requirements. Association approval and city permitting remain separate steps in planning the work.

Permits issued by: City of Celina Building Services Division

How we build in Celina

The same engineering standards apply on every job, whatever the property.

  • Direct employeesOur own crews set every post, pour every footing and wire every operator. We never use subcontractors.

  • Footings to depthStructural posts go into concrete to the one-third depth rule, so expansive clay cannot heave them out of line.

  • Safety standardsAutomated gates are built to ASTM F2200 geometry and wired to UL 325, with sensors tested before handover.

From Site Measurements to Final Testing

We establish the permitted layout before excavation and carry it through installation and testing.

  • Assess the site, measure openings and locate proposed boundaries against setbacks and easements.
  • Request utility locating before digging and review marked utilities against the excavation layout.
  • Write the scope, prepare permit documents and address applicable HOA paperwork.
  • Our direct employees install concrete footings using the one-third depth rule and applicable minimums.
  • Walk through completed work, testing gate travel, controls and safety sensors where installed.

Where we work in Celina

Light Farms, Mustang Lakes, Cambridge Crossing, Sutton Fields, Lilyana, Mosaic

Nearby cities we also serve

Prosper, McKinney, Frisco, Allen, Plano, Denton

What affects the cost in Celina

For Celina projects, cost depends on the approved layout as well as the selected material. Corner setbacks can change the fence run. Drainage easements can require a different alignment, while boundaries adjoining open space may require black tubular steel rather than wood. We establish these constraints before defining material quantities.

Wood-fence height affects footing depth, excavation and concrete quantities. Access for equipment, removal of existing fencing, and the condition of reusable supports also shape the scope. Gate projects add structural, operator and electrical requirements. We account for applicable permits and separate repair work from replacement work in the written scope.

Questions from Celina property owners

How tall can my residential fence be?
Within city limits, residential fences may not exceed eight feet, excluding ground clearance and decorative caps. We establish the proposed height before selecting posts and footing details. If your property has HOA architectural requirements, we also need those documents before finalizing the design.
Can I put a fence in a drainage easement?
No. City rules prohibit fences in drainage easements, so the proposed run must stay outside that area. Fences adjoining floodplains, creeks or dedicated open space must also be black tubular steel and at least 50% open. We check those boundaries before specifying materials.
What changes when my property is a corner lot?
The fence must remain at least 15 feet from the curb face unless the Director approves otherwise. We measure that setback before fixing the fence line and adjoining gate position. It can change the enclosed area, entrance arrangement and quantities included in the scope.
Does a fence repair need a permit review?
The city’s building-permit requirement covers construction, alteration, repair and improvement of buildings or structures within city limits. We confirm which category applies to the proposed fence repair with Building Services. The scope should identify damaged components and planned replacements so the permit question addresses the actual work.

Plan Your Celina Gate or Fence Project

To check Celina’s fence setbacks, provide your location and gate width or fence length for our site assessment and written quote.

Contact Star Gate And Fence See our projects
Gates Fences Gate Repair Gate Installation Outdoor Construction Carports